Craftsman 26 5-drawer Standard-duty Tool Chest &

OPERATOR'S MANUAL

accepted duty tool chests

• Sporadically the drawer fronts, drawer trim, and other surfaces should be cleaned with a mild purifying and water system.

• Auto wax will conserves the unit's splendor finish. Utilise the mount as to a cable car. The full leave besides assistanc protect the unit against scratches.

• Grease and oil can be removed with most standard cleanup fluids. For safety, use a nonflammable cleansing fluid.

• If drawer liners are supplied, it is recommended they are used to protect the finish inside the drawers and to make the drawers easier to clean. The drawer liners English hawthorn be clean with Georgia home boy and water.

* Product you purchased Crataegus oxycantha vary from picture shown

SERVICE PARTS

Call 1-800-366-7278 for Service Parts. Refer to Service Parts Drawing for full listing of Service Parts.

Location Manikin # Information

Model numbers and strange information required for overhaul parts is located on a label on the midland right side of the top most draftsman.

capacities

• The upper limit weight for from each one drawer should be no to a greater extent than

30 lbs.

• The maximum product weight, including contents, should be no more 300 lbs. for each model combination with 3 x 1 edge in casters. The maximum product weight, including contents, should be no more than 500 lbs. for apiece exemplar combination with 4 x 2 inch casters.

sustentation

• For casters, use of goods and services high quality bearing grease, (every year).

• Lubricate the slides with grease or combining weight,(double yearly.)

• Lubricate lock with graphite, (yearbook).

Ball bearing

	base hit
DANGER	is exploited to indicate a dangerous situation which,
if not avoided, wish result in serious injury operating room death.
WARNING	indicates a hazardous situation which, if not

avoided, could result in serious harm or death.

Caution is old to suggest a dangerous situation which, if not avoided, may result in minor injury, limited injury, or prop damage.

CAUTION: Read and follow all Rubber Rules and Operating

Instructions before first use of this product.

Peril

• Arrange NOT resist on this merchandise. You may fall, which may do personal injury.

• DO NOT deputize drawers. You May fall, which Crataegus laevigata cause personal injury.

• USE Brake system when non moving this product. This will preclude the product from rolling, which Crataegus oxycantha cause personal wound or intersection damage.

• APPROPRIATELY SECURE this product before moving with a forklift.

• DO Non tow with great power equipment. The product could wind, which may cause personal injury or prduct equipment casualty.

WARNING

• WEAR SAFETY Spectacles when removing or repositioning the slides. The creature could slip, which may cause personal injury.

• DO Non wax this product on a truck know or any other moving object. This whitethorn cause personal trauma or product legal injury.

• Doh NOT alter this product in any manner. E.g., do not Reseda luteola external lockbars or tie electrical equipment. This may get own injury or product impairment.

• UNIT Moldiness BE located on A level surface. The product may get ahead unstable and bung if stored operating theater moved on an un-level surface, which whitethorn causal agent personal hurt or product damage.

• Lock u the bloomers before vibrating this product. The shorts could come unresolved and make the production unstable and tip, which may cause personal injury or product damage.

• Act NOT pull this intersection when whirling it. Push the product to prevent personal hurt.

CAUTION

• BE CAREFUL when opening more than one drawer. The mathematical product whitethorn become unstable and point, which may cause personal trauma or product wrong.

Sears Brands Management Corporation, Hoffman Estates, IL 60179 USA

F1976

hardware

TOOLS Compulsory:

Flat-tip Screwdriver

3/8-in. Wrench

7/16-in. Wrench

5/16-in. Drill Bit

HARDWARE REQUIRED:

Midsection Chest

1/4 - 20 x 5/8" (Qty: 4)

1/4 - 20 Nut (Qty: 4)

Ironware REQUIRED:

Cabinet

1/4 - 20 x 5/8" (Qty: 16)

1/4 - 20 Crank (Qty: 16)

HARDWARE REQUIRED:

TOOL CENTER

1/4 - 20 x 5/8" (Qty: 16)

1/4 - 20 Nut (Qty: 16)

1/4-14 x 5/8 Sheet Metal Screw (Qty: 4)

Carton Contents

Chest of drawers:

Literature

Cabinet:

Lit

Hardware bag

Caster pack

Castor pack

ASSEMBLY

Note: Not all meeting place instructions wish apply to your good example.

Dispatch Chest From Rolling Cabinet

(Tool Center of attention)

• The whole comes with the chest secured to the inside of the cabinet by either two or four 1/4-14 x 5/8 screws.

• Lay the cabinet down on its back. Use packaging embodied to protect the rouge finish.

• Remove the securing screws from the underside of the cabinet. Spare the screws for mounting the pectus to the cabinet.

• Murder the chest.

CASTER INSTALLATION

Items Requisite:

1/4-20 x 5/8" Screw (Qty: 16)

1/4-20 Positional notation Nuts (Qty: 16)

Process:

NOTE: Use sufficient manpower for this operation.

• Open the bulge storage panel surgery get rid of nether drawer. (Relate to Operation section Removing Knickers)

• Put over the whole on its back, habituate packaging corporal to protect the blusher finish.

• Attach the casters to unit victimisation (4) 1/4-20 x 5/8" screws and (4) 1/4-20 nuts per castor. Mount some swivel casters on the same side of the unit. Wrench-tighten.

• Return the unit to its statant position.

• Close the bulk storage panel or supervene upon drawer.

Nut

Screw

OPTION 1 - mounting Top chest To Intervening chest

• Get rid of enough drawers to access the top and bottom climbing surfaces of the units (refer to the drawer removal instructions).

• Place the chest in the desired location on top of the middle thorax and strike off the mounting hole locations.

• Remove the pectus and drill four 5/16" (8mm) holes through the top of the intervening chest.

• Secure the units unitedly using four 1/4- 20 x 5/8 inch screws.

• Wrench tighten all screws.

• Replace the drawer (refer to the drawer installation instructions).

• To remove the chest, reverse the procedure.

OPTION 2 - mounting chest to

Tool Center Cabinet

• Remove the top drawer from the cabinet (refer to the drawer remotion instructions).

• Lift the chest onto the cabinet. Draw up the holes in the bottom of the chest with the holes in the pass of the cabinet.

• Attach to the chest of drawers using two 1/4-14 x 5/8 screws that were utilised to secure the dresser to the bottom of the cabinet.

• Wrench constrain every last screws.

• Replace the draftsman (cite to the drawer installation instruction manual).

• To remove the chest, reverse the routine.

cognitive operation

REMOVING DRAWERS
• Empty the draftsman.
• Full extend the drawer	Release

Prise Title - Lift Beaver State glower (depending connected the lantern slide) the release lever on both sides, (this allows the slides to ride over the stops). Pull out to bump off.

reinstall drawers

Ball heading slides - Pluck slides and slide aircraft carrier out to in full extended position (determine illustration). Hold the slide connected the cabinet piece aligning IT with the slide happening drawer.

Slimly tuck one side and repeat for the other side. Slow push drawer to its full closed position to engage slide. Naked draftsman and reclose to ensure proper operation.

Slide Carrier

Microscope slide

Craftsman 26 5-drawer Standard-duty Tool Chest &

Source: https://manualmachine.com/craftsman/5drawerstandarddutyballbearingtoolcenterred/1938309-use--care-manual/

Share this post